Zircon MetalliScanner MT7 Concrete and Wall Metal Detector – DeepScan Metal Locator for Rebar, Pipes, and Hidden Objects up to 6 in. Deep with LCD Readout and Pivoting Handle
$189.99
Related Products
The Zircon MetalliScanner MT7 is a deep-sensing metal detector designed for professional and serious DIY applications. It accurately locates metal objects such as rebar, copper pipe, conduit, nails, and other embedded hardware behind concrete, tile, plaster, drywall, or masonry surfaces. With both Standard Scan and DeepScan modes, the MT 7 can detect typical metal targets up to 6 inches deep, helping users identify hazards and avoid costly mistakes before drilling, coring, or cutting. A bright backlit LCD provides metal type identification, depth measurement, and directional arrows that guide you toward the strongest signal. Its ergonomic design includes a pivoting handle, rubberized grip, and integrated lanyard loop for comfortable use on floors, walls, and ceilings. The tool comes complete with a 9V battery and a protective case, ensuring you’re ready to scan right out of the box. For contractors, electricians, plumbers, inspectors, and remodelers, the MT7 delivers accurate, dependable metal detection that improves safety and efficiency on every job.
LOCATE METAL QUICKLY: Detects rebar, pipes, conduit, nails, and hidden metal behind concrete, tile, plaster, drywall, or masonry—perfect for safe drilling, cutting, or renovation projects. Professional-grade rebar and pipe locator for concrete, masonry, and construction surfaces — features backlit display and dual scan modes.
DUAL SCAN MODES: Switch between Standard Scan for everyday wall or slab detection and DeepScan Mode to find metal up to 6 inches (15 cm) deep.
CLEAR DEPTH AND METAL READOUT: Bright backlit LCD display shows metal type (ferrous or non-ferrous), depth measurements in inches or centimeters, and directional arrows for precise target location.
ERGONOMIC PIVOTING HANDLE: Comfortable rubberized grip with pivoting handle and built-in lanyard loop makes scanning walls, floors, and ceilings effortless—even over large areas.
READY TO USE: Comes with a 9V battery and protective carrying case, so you can scan immediately and keep your MetalliScanner MT7 protected between jobs.
8 reviews for Zircon MetalliScanner MT7 Concrete and Wall Metal Detector – DeepScan Metal Locator for Rebar, Pipes, and Hidden Objects up to 6 in. Deep with LCD Readout and Pivoting Handle
Add a review
$189.99
Robert007 –
Great tool
Scanner works very well. Nice box to keep tool safe.
FG –
Great scanner. Very accurate!
Great scanner! Use this at every Wind Mitigation Inspection in Florida.
E –
Will not fine wire mesh
I bought this unit hoping to determine if my 4″ concrete garage slab has wire mesh installed in it. If you follow the directions and calibrate the finder in open air and then proceed to use it on the concrete slab it says their is ferrous metal throughout. The results seemed inaccurate so I did what the directions say and then calibrated it on the surface to be tested but “away” from any metal. I did this but their is no way to recalibrate it away from ferrous metal if you dont know where OR IF their is any ferrous metal. I then proceded to test a 12″ x 12″ x 3″ landscape block. Again calibrate it in air and then onto the landscape block (which I suspended in air on a clean piece of wood) and once again it said the block had ferreous metal in it which I know it does not because I broke one open. I then recalibrated the unit on the landscape block and it now shows non ferrous metal in various spots. I then held a 1/2″ rebar beneath the block and it showed the bar but a full one inch deeper than it really was. Long story short is this unit will not detect if a concrete floor slab has wire mesh installed in it (not rebar). I am only looking to determine if wire mesh is present and not a specific location (depth or otherwise). I would like to return the unit but I used it as noted above. For what it costs this unit gave no better a result than a cheap stud/wire/metal finder for $25 bucks, that I also bought and tried..
Stefan Bond –
Necessary for home inspectors in Florida
I utilize this on many of my wind mitigations. It’s a reliable tool and comes in a case which really helps.
Kris Beall –
Great tool for Home inspectors who do wind mitigation reports!
Easy to use and accurate!
russ –
you need to practice
I used this to find the tension cables in my house foundation. But you need to understand how to use this device and there are videos on youtube you need to watch. Takes a bit of practice. The idea is to find the beginning point and end point of detection, then the middle between is the cable location. Its not like cable/nocable. The reason is the deeper the cable the more faint the detection. Also its a good idea to calibrate the device after you place it on the ground where you are going to detect.
Primus –
Accurate.
I bought this as a new home inspector after seeing blogs from others in my trade who recommended it. First few uses and it performs extremely well so far.
Brian Hanrahan –
Pipe finder metal detector
It has a bit of a problem going through concrete and ceramic tile but it works I just need to know where I have to drill holes through the side of my slab to get new water lines into my house